Brocade Switch Zone Configuration

Bkp_Bro1:admin> alicreate "PRACDB01_S1P21", "21:00:00:1b:32:1c:3c:0c"
Bkp_Bro1:admin>
Bkp_Bro1:admin> zonecreate "PRACDB01_s1_9990_1E", "PRACDB01_S1P21; SE9990_1E"

Bkp_Bro1:admin> cfgadd "PROD_TAPE_ZONE1", "PRACDB01_s1_9990_1E"
Bkp_Bro1:admin> cfgsave
You are about to save the Defined zoning configuration. This
action will only save the changes on Defined configuration.
Any changes made on the Effective configuration will not
take effect until it is re-enabled.
Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y
Updating flash ...

Bkp_Bro1:admin> cfgenable "PROD_TAPE_ZONE1"
You are about to enable a new zoning configuration.
This action will replace the old zoning configuration with the
current configuration selected.
Do you want to enable 'PROD_TAPE_ZONE1' configuration (yes, y, no, n): [no] y
zone config "PROD_TAPE_ZONE1" is in effect
Updating flash ...


2nd Port
============
Bkp_Bro1:admin> alicreate "PRACDB02_S1P22", "21:00:00:1b:32:83:7c:71"

Bkp_Bro1:admin>
Bkp_Bro1:admin> zonecreate "PRACDB02_s1_9990_1E", "PRACDB02_S1P22; SE9990_1E"

Bkp_Bro1:admin> cfgadd "PROD_TAPE_ZONE1", "PRACDB02_s1_9990_1E"
Bkp_Bro1:admin> cfgsave
You are about to save the Defined zoning configuration. This
action will only save the changes on Defined configuration.
Any changes made on the Effective configuration will not
take effect until it is re-enabled.
Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y
Updating flash ...

Bkp_Bro1:admin> cfgenable "PROD_TAPE_ZONE1"
You are about to enable a new zoning configuration.
This action will replace the old zoning configuration with the
current configuration selected.
Do you want to enable 'PROD_TAPE_ZONE1' configuration (yes, y, no, n): [no] y
zone config "PROD_TAPE_ZONE1" is in effect
Updating flash ...




Switch 134
=============


Bkp_Bro2:admin> alicreate "PRACDB01_S2P21", "21:00:00:1b:32:83:a0:77"
Bkp_Bro2:admin> zonecreate "PRACDB01_S2_9990_2E", "PRACDB01_S2P21; SE9990_2E"
Bkp_Bro2:admin> cfgadd "PROD_TAPE_ZONE2", "PRACDB01_S2_9990_2E"
Bkp_Bro2:admin> cfgsave
You are about to save the Defined zoning configuration. This
action will only save the changes on Defined configuration.
Any changes made on the Effective configuration will not
take effect until it is re-enabled.
Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y
Updating flash ...
Bkp_Bro2:admin> cfgenable "PROD_TAPE_ZONE2"
You are about to enable a new zoning configuration.
This action will replace the old zoning configuration with the
current configuration selected.
Do you want to enable 'PROD_TAPE_ZONE2' configuration (yes, y, no, n): [no] y
zone config "PROD_TAPE_ZONE2" is in effect
Updating flash ...
Bkp_Bro2:admin>


2nd port
========


Bkp_Bro2:admin> alicreate "PRACDB02_S2P22", "21:00:00:1b:32:84:76:72"
Bkp_Bro2:admin> zonecreate "PRACDB02_S2_9990_2E", "PRACDB02_S2P22; SE9990_2E"
Bkp_Bro2:admin> cfgadd "PROD_TAPE_ZONE2", "PRACDB02_S2_9990_2E"
Bkp_Bro2:admin> cfgsave
You are about to save the Defined zoning configuration. This
action will only save the changes on Defined configuration.
Any changes made on the Effective configuration will not
take effect until it is re-enabled.
Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y
Updating flash ...
Bkp_Bro2:admin> cfgenable "PROD_TAPE_ZONE2"
You are about to enable a new zoning configuration.
This action will replace the old zoning configuration with the
current configuration selected.
Do you want to enable 'PROD_TAPE_ZONE2' configuration (yes, y, no, n): [no] y
zone config "PROD_TAPE_ZONE2" is in effect
Updating flash ...